Mimaki 全彩色 Photopolymer

High Definition 全彩色

材料喷射

材料信息

关于 High Definition 全彩色

Using the UV curing inkjet process, the UV ink (CMYK, White) is cured layer by layer. This can produce objects with more than 10 million different colors. Final parts can satisfy professionals’ exacting requirement to make full color and fine modeling of high details, 例如, 数据, 3D maps and architecture mock-ups. And the post processing like over coating and attachment of screws is also able to apply to an object after printing.

Color & 完成

全彩色
标准
This finish has the supports removed and the parts are rinsed. Parts may have partial shiny surfaces and staircasing may be noticeable in hard light conditions.
不光滑的
This finish has the supports removed and the parts are rinsed, then an additional matte coating is applied to reduce layer lines.

技术

  • 材料喷射

描述

应用程序
Figurines, 医疗 models, 体系结构 models, Realistic visual prototypes
材料了
Vivid full color, Photorealistic color accuracy, Fine details

设计指导方针

边界框

边界框马克斯
495 x 495 x 300毫米

边界框最小
2.5 x 2.5 x 2.5 mm

The bounding box is a 3D imaginary outline of a box that encloses the smallest area occupied by your model. Your model must be within the minimum and maximum bounding box sizes. If the size of the model is close to the maximum bounding box, then the printing orientation will be restricted.

支持ed Wall Thickness 最小值
1.0 mm
Unsupported Wall Thickness 最小值
1.0 mm
A supported wall is connected at least on two sides of the wall, while an unsupported wall is connected only on one side of the wall. 墙 that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wall geometry of the model. Please consider the size of your model and reinforce the walls or add support structures as needed as minimum guidelines will not always be adequate for large models.

电线

支持线分
0.8 mm
不支持的电线敏
1.0 mm
金属丝是圆形的, rectangular or even triangular feature that is thinner in its unconnected directions than its length. A supported wire is connected at least on two sides of the model, while an unsupported wire is connected on one side of the model. 电线 that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wire geometry of the model. Please consider the size of your model and reinforce the wires or add support structures as needed as minimum guidelines will not always be adequate for large models.

Details

分钟浮雕细节
0.8 mm
最小细节雕刻
0.8 mm
用于文本, the ratio between width and depth, should be 1:1 and sans-serif fonts are preferred for line weight consistency.

逃离黑洞

Single Escape Hole Diameter (最小值)
3.0 mm
Multiple Escape Hole Diameter (最小值)
1.0 mm
Escape holes are necessary to empty the support material of a hollow model. Two escape holes at the opposite ends of the model is optimal for the support removal process. Please consider the size of your model and make the escape holes bigger or add more escape holes as needed as minimum guidelines will not always be adequate for large models.
A single escape hole at the end of a cavity will not allow material in the corners near the escape hole to fully escape. So we recommend multiple escape holes at both ends of the cavity.

间隙

最小值
0.4 mm
间隙 is the space between two individual parts in a model. If the space among the individual parts do not meet the minimum clearance, then parts can fuse together or can be difficult to clean. This is important for movable pieces like hinges, gears, etc.

浇口

0.8 mm

浇口 are wires that keep two or more parts together. Parts should be connected with a minimum of two sprues each. Please consider the size of your sprues and increase them as needed as minimum guidelines will not always be adequate for large models. If the sprues are within the guidelines and are broken, but there is no damage to your model, we will still ship them as is.

联锁 & 封闭的部分

联锁
是的

随信附上
No

部分文件

马克斯
99

精度

精度 ± 0.05 mm +0.25%
For example: a product with dimensions of 50 x 50 x 100 mm can be 0.05 mm + 0.0025*100 mm = 0.3 mm bigger or smaller in any direction.

相关材料

Also Known As Frosted Detail Plastic, Resin-based Acrylic Plastic, Photopolymer, VisiJet M3 Crystal
细节的塑料
应用程序: Scale Models, 最小值iatures, 珠宝 Prototypes, Mold Masters
了解更多→
多色Polyjet
应用程序: 医疗 Models, Teaching Aids, Visual Prototypes, Demonstration Displays
了解更多→

Stay up to date on promotions, case studies, and more.

友情链接: 1 2 3 4 5 6 7 8 9 10